Black stripes can be made arbitrarily. For example, every 2 rows, as well as on the legs
1. Into magic ring 6 sc
2. (1sc, inc) * 3 = 9
Stuffing along the way is very loose, you can insert the wire and push it deeper into the body.
3-28.9 sc
29. (2sc, dec) * 2, 1sc = 7
30-34.7sc
Leave the thread for sewing.
Sew the tail under the first black stripe
Sew the hind paws to the body, so that the part of the body protrudes above and slightly behind them. Flatten the hips and press them more tightly to the body, secure with needles and sew.
Make sure they are symmetrical.
The front legs are sewn in the same way, but make sure that the feet are level with the hind legs. For convenience, you can pierce one front leg with a knitting needle, then the body and the other leg and put the tiger cub. If it is stable, you can sew on. If not, then you need to correct your legs (raise or lower).
Head
We start with white.
1. Into magic ring 6sc
2. (inc) * 6 = 12
3. (1sc, inc) * 6 = 18
4. (2sc, inc) * 6 = 24
5-7. 24 sc
The marker goes down the center of the bottom of the head. In the process of knitting, align the offset loops so that it goes strictly in the center.
8.4sc, inc, inc, 2sc, (inc) * 8, 2sc, inc, inc, 4sc = 36
9.White 5sc, inc, inc, 3sc, red 1sc, then behind the rear PPs (for the left front PPs we will knit the nose pad) 1hdc, increase hdc, 2hdc, increase hdc, 1hdc, (increase hdc) * 2, 1hdc, increase in hdc, 2hdc, increase in hdc, 1hdc, then for both points 1sc, white, 3sc, inc, inc, 5sc = 46
10.White 6sc, (inc) * 3, 4sc, red 20 hdc, white 4sc, (inc) * 3, 6sc = 52
11.White 7sc, (inc) * 3, 4 sc, red 2sc, 20hdc, 2sc, white 4sc, (inc) * 3, 7sc = 58
12.White 9 sc, (inc) * 3, 4sc, red 3sc, 20hdc, 3sc, white 4sc, (inc) * 3, 9 sc = 64
13.White 18sc, red 4sc, 20hdc, 4sc, white 18sc = 64
Then we knit only red
14- 20.64 sc (7 rows)
21.9sc, dec, 1sc, dec, 36sc, dec, 1sc, dec, 9 sc = 60
22-24.60sc (3 rows)
25. (8 sc, dec) * 6 = 54
26. (7 sc, dec) * 6 = 48
27. (6sc, dec) * 6 = 42
28. (5sc, dec) * 6 = 36
29. (4 sc, dec) * 6 = 30
30. (3 sc, dec) * 6 = 24
31. (2sc, dec) * 6 = 18
32. (1sc, dec) * 6 = 12
33. (dec) * 6 = 6
Pull off the hinges
Pad on the nose.
We knit in rotary rows
1.Kit in the center from the left sts 10 sc
2-3. 10 sc.
4.Dec, 6 sc, dec = 8
five . Dec, 4 sc, dec = 6
Sew on after nose tightening.
Nose tightening.
Insert the needle from the bottom of the muzzle between 7 and 8 rows, bring it out above the ka by 3 rows, throw the thread over the top of the muzzle and re-insert the needle from the bottom and up. Tighten.
Sew an overlay on the muzzle on top.
Eye tightening.
Look at the photo.
Insert the needle from the bottom of the head into the first red row, bring it into the eye area (this is the first extra row of hdc and the edge of the bridge on the nose and grab 3 sc to the bridge of the nose) and return back down. Pull off.
The second is similar. Between the eyes 12 hdc
